![accel fuel injection kits accel fuel injection kits](https://www.toolsource.com/images/prod_images/SGT38000_1200Wx1200H.jpg)
To start with, turn the key to the on position and then find Go EFI Tuning on The accel pump function to increase or decrease the fuel added on acceleration. IAC steps are between 3-10 at warm idle, then your next step would be to adjust If the system is having hesitation or bogging issue, and your The settings in intervals of 10 to find which way you need to adjust the system Startup issues, along with setting the IAC. Changing these settings should help with your Starts add or subtract fuel from Crank fuel 65f, for hot starts add or subtractįuel from crank fuel 170f. There, you will see three cranking fuel selections. With the key turned on, go to the Go EFI Tuning menu, find CrankĪnd Warm-up. In this menu, highlight one of the backup files you wish to save to and thenĮither press OK on the screen or push the joystick IN, and it will save all Then find Read Cal from ECU on the main menu and then select it. To save a tune, first, turn the key to the On position, not You can also copy and paste these files and send them to our You can click on these, and they will bring up an Excel file showing the data This folder and inside you should see several files inside that say Dashboard, Handheld folders come up, on-screen find the folder labeled log_file. Not go to My Computer and you should see a removable drive, select it.
#ACCEL FUEL INJECTION KITS PC#
You should see a prompt on your PC to open the handheld folder, if Handheld will light up with three menu options, USB mass storage is at the top, Take the handheld to your PC and plug in the USB cable and handheld. Seconds for the data on the dashboard to go black. Then you can turn the vehicle off and wait 15 Once you finish the drive, you will press the button again, and Now you will drive the car and get it to have the issue youĪre having. Press the joystick on the right of the screen IN, and a message will pop up When the vehicle is running, go onto the dashboard screen and This allows for exact adjustments to be made ItĪllows you to check how the many functions the system can read and go through You have now reset the learn function.ĭata logging is a useful tool for diagnoses and tuning. The key off and wait for the numbers in the value side to go black. Menu and then up to the Dashboard and select it. Highlight this and push right on the joystick to go to #1, then save that to To reset the learn is a very easy procedure. If this happens, itĪlters the fuel map in ways that may not be optimal for proper running the Will try to compensate in order to keep the car running. Sometimes if there are outside problems such as bad misfires, exhaust leaks, orĪny other situation that could cause poor readings on the O2 sensor, the system System uses to adjust the active fuel tables it is using for operation. Once the throttle screw is in the correct position key the ignition off and allow the system to save.Īll Fitech EFI systems have learning procedures that the If the number is above 10 then turn the screw IN (clockwise) until the IAC Steps are between 3-10. If the number reads zero then slowly turn the screw OUT (counter clockwise) until the IAC Steps reads between 3-10. This number needs to be within 3-10 at warm idle. On the handheld go back to the Main Menu and enter into Dashboard. Once engine is running and at operating temperature turn ON Idle Set Mode. If the engine wont stay running without keeping your foot on the pedal a little turn the throttle adjustment screw clockwise another half turn.
![accel fuel injection kits accel fuel injection kits](https://images-na.ssl-images-amazon.com/images/I/71t4XtVR2KL._AC_SL1500_.jpg)
To get engine to start you may have to press the throttle pedal slightly. Enter into this menu and start the engine. Turn the key on and go to Initial Setup on the hand held. Once this happens, turn the ignition key to the Once in the dashboard, turn the ignition key off and waitįor all the data to blackout. Now go to Go EFI Initial Setup, then Engine Setup, now input all of the parameters that are needed for your application, making sure to save each one individually.Īfter you have entered your information and saved it, go up and After this is done it will revert to the main menu.
#ACCEL FUEL INJECTION KITS DOWNLOAD#
Once on this file select it, and it will download to 100 percent. Once in this menu scroll down to the second to last selection, it should say Default v8 T195. These are a basic overview of the most common setup questions.įrom the main menu, go to the very bottom and select Write Cal To ECU.